Video: How To Change Your BMW Automatic Transmission Fluid (320i, 325i, 328i, 330i, 335i, 530i, 630i, X3, Z4)

Blog Feature

If you haven't serviced your BMW's automatic transmission, you're driving around in a ticking time bomb. Just like your engine, your transmission relies on oil for cooling and lubrication.

Servicing your transmission will extend its service life as well as ensuring it continues to operate at it's full potential. If your transmission is shifting slowly, sloppily, or if it's overly loud, these are good signs that it's time to perform a transmission service. 

 

Tools needed to complete this repair:

Parts needed to complete this repair:


Step 1: Lift your Car

Safety is key. Here at FCP Euro, we have the luxury of an automotive lift. Whether you are using a lift or completing this job on jack stands, take every precaution to make sure the car is secure. If using stands, place wood blocks or spare wheels under the car as an added backup.

 

Step 2: Remove Transmission Splash Guard and Exhaust Support Bracket

Using an 8mm socket, remove the screws that hold the trans splash guard in place. 
BMW Automatic Trans Splash Guard

 

Step 3: Loosen Trans Fill Plug and Remove Drain Plug
Before you start draining the oil, loosen the trans fill plug using an 8mm Allen socket. Doing this creates a vent and allows the oil to flow more freely. Now you can place your fluid catch pan under the transmission and remove your drain plug using a 10mm Allen socket. 

BMW Automatic Trans Drain Plug

 

Step 4: Remove Transmission Pan Screws, Exhaust Support Bracket and Remove Pan 
Using a T40 Torx bit, remove the transmission pan screws. By leaving the screws opposite of the drain plug in place, you can drop the drain lower to more effectively drain the oil. 

There's an exhaust support bracket that needs to be removed to access all of the transmission pan screws. Use a T35 Torx socket to remove this.

BMW Automatic Trans Pan Screws

BMW Automatic Trans Exhaust Brackets

BMW Automatic Trans Removal

 

Step 5: Clean Mating Surfaces
Often an overlooked step, cleaning the mating surfaces for the new transmission oil pan is mandatory. Without doing this, you risk having leaks - either immediately after completing this job, or not too far down the line. Simply use a lint-free rag or shop towel to make sure there's no debris or significant amounts of old oil.BMW Automatic Trans Clean

 

Step 6: Install New Transmission Oil Pan
Since our BMW comes with the plastic transmission oil pan, our kit comes with the new pan that has an integrated filter. Before installing the new pan, make sure to lubricate the o-ring to ensure proper sealing. 

Holding the pan in place, start all the T40 Torx screws by hand until they're just snug. From this point, you can follow the torquing procedure and torque all the screws to the specified 10N•m. The image below demonstrates the correct order. Once they're all tightened, it can't hurt to go around in the same order one more time to ensure that none loosened up. 

BMW Automatic Trans New Pan

BMW Automatic Trans Lubricate O-Ring

BMW Automatic Trans Torque Procedure

 

Step 7: Fill Transmission
Before starting the fill procedure, make sure the drain plug is installed. The new pan in the kit has it pre-installed, however, it's worth checking once more. There's nothing worse than going to fill the transmission and watching oil spill out all over your garage floor. 

Using our fluid transfer syringe, begin filling the transmission. We highly recommend using this syringe as the fill plug is difficult to access. A fluid transfer pump would work as well in this scenario as it was used in this older video. You want to fill the trans until it begins to overflow. Now you can loosely install the fill plug.  

BMW Automatic Trans Fluid Fill

 

Step 8: Run Through Gears
Unfortunately, this next step requires you to take the car off the jack stands or your lift. With the car on the ground, you want to firmly apply the brake pedal, put your transmission in gear and run through all the gears. Do this until your car is up to optimal temperature. You can find this temperature listed on the side of the transmission oil pan. To determine if your car is properly up to temperature, use an OBDII scan tool that outputs this data. 

BMW Automatic Trans Gears BMW Automatic Trans Temperatures BMW Automatic Trans Scan Tool

 

Step 9: Final Transmission Fill
Using safe jacking practices, get your car up in the air once again. Just like before, continue adding more transmission fluid until it begins to overflow. Once it does, you can install the fill plug for the final time.

 

Step 10: Reinstall Exhaust Support Bracket and Splash Guard
Now you're simply reversing the order of step two. I would wait until the car cools down since you will be working around the exhaust. 

BMW Automatic Trans Reassembly

 

Doing this quick service every fifty-thousand miles will ensure that your transmission functions optimally for the course of its life. If you're wondering which kit you specifically need, click the link below and use the "My Garage" vehicle search. And as always, make sure to subscribe for more videos

 

 

New Call-to-action

 

New Call-to-action